Traditionally, cyclists’ training has involved three things: 1) ride your bike, 
2) ride your bike and 3) ride your bike some more. However, it can be very difficult to improve the strength and control of a specific muscle group responsible for a part of your pedal stroke just by riding the bike.

The pedal stroke can be broken down into four phases, with different muscles responsible for each phase. Weight training is a very time-efficient way specifically to strengthen these muscles.

Cycling is a single-leg activity; while one leg is pushing through the power stroke, the other leg is doing the opposite action. Therefore, it is important to train using single-leg exercises that encourage independent activation and challenge the body’s core control. 

To develop control and muscular endurance, the exercises can be performed just using body weight. A slow tempo is important to develop control of the movement (four seconds down, hold for two seconds at the bottom, push up quickly). Two-three sets with high repetitions (12 to 15 repetitions) with 90 seconds’ rest between sets will help to develop endurance.

To increase strength and muscular activation, the exercises can be loaded with dumbbells in the hands or a bar across the shoulders. Perform three-five sets with fewer repetitions (three-five) but with longer rests between sets (three-five minutes) and at a higher tempo (two down, two up).

It’s also a good idea to have your bike set up on a turbo and gently ride between sets to remind your legs where and how you’ll integrate each exercise back into the pedal stroke.

Phase one

Before top dead centre
to power stroke

Target: Drive pedal forward over the top of the stroke and start to push down.

Muscles targeted: Quadriceps 

Exercise: Lunge

Step forward, keep the chest up, drive the knee over the foot and drop the back knee down until it nearly touches the ground. Push down and back through the heel of the front foot to return to the starting position.


Phase two

Mid power stroke

Target: Drive the pedal straight down 

Muscles targeted: Gluteus maximus and quadriceps

Exercise: Split squat

Step back with the non-exercising leg and keep your weight going down through the heel of the forward support leg. Drop hips straight down, until the rear knee almost touches the floor. Squeeze the glutes and push straight down through the heel of the front leg to return to the start position.

Phase three

Power stroke past bottom dead centre 

Target: Scrape the pedal quickly through the bottom of the pedal stroke so the other side gets onto the power stroke more quickly.

Muscles targeted: Gluteus maximus 
and hamstrings

Exercise: Single leg dead lift

Start holding the bar in front and pinch the shoulder blades back and down, keeping the back straight throughout. Stand on one leg, sway the hips back and bend the knees slightly. Slide the weight down the front of the thighs towards the ground, squeezing the glutes to control the descent 
with your weight through your heel. Drive through the glutes to return to a standing position.

Phase four

Back dead centre 
to recovery stroke

Target: Continue to rearward travel of the pedal and reduce the resistance on the pedal as it travels up the back of the pedal stroke.

Target muscles: Hamstrings

Exercise: Single leg Swiss ball hamstring curl. Lie on your back with your heels on a Swiss ball, knees bent at 90°. Squeeze your glutes, push the hips up off the ground, balancing on the shoulders, and straighten one leg. Extend the support foot out until the knee is nearly straight. Return leg to the start position. Keep your core contracted and glutes squeezed throughout.

This article was first published in the Autumn 2012 issue of Cycling Fitness. Read Cycling Weekly magazine on the day of release where ever you are in the world International digital edition, UK digital edition. And if you like us, rate us!

  • Jennifer Sage

    I’m trying to figure out how the gluteus maximus is still contributing in “Phase 3″? The hip extension is completed at the point, and GM is a hip extender…

    …and no mention of hip flexor contribution (though small) in Phase 4, the hip flexing portion of the stroke?

  • Dave Smart

    “Cycling is a single-leg activity”. We couldn’t see a more ridiculous statement under the heading – ‘Perfect Your Pedalling’. Pedalling is only a single-leg activity when you’re riding without cleats, but this guy obviously isn’t!! ‘Pedalling-in-circles’ means applying tangential (i.e. horizontal) forces when the cranks are vertical. The quads push the top foot forward and the hamstrings pull the lower foot back. Blimey! – both legs working together, in perfect unison. Nobody will ever learn that, with the plantar-flexion of the ankles shown in Phase 3, and single-leg dead lifts are more likely to injure the spine than strengthen the hamstrings. Terrible advice.

  • ted hutton

    get a fixed wheel set up then you will have to pedal properly lots of us olduns did that in the

    1950′s why not give it a try.

  • Dave Smart

    “It is important to train using single-leg exercises that encourage independent activation and challenge the body’s core control.” – That’s devoid of intellectual rigour, judged by the advice that follows:- “It’s also a good idea to have your bike set up on a turbo and gently ride between sets to REMIND your legs where and how you’ll integrate each exercise back into the pedal stroke.” In fact, nobody actually pedals with one leg, once their feet are attached to the pedals. This is because it is far more efficient, and relaxing, to balance the action and reaction from each leg to the other, as you ‘pedal in circles’. You will never learn that sweet co-ordination/muscle control from single-leg exercises. Your silly analysis would only hold true if you’re riding without cleats!! 45 years ago I built myself a machine to lift a weight with the cranks, so the strength exercise was precisely the SAME as the muscles’ action on the bike. Think about it.